Studi Struktur Portal Baja Gedung Workshop Alat Berat Di Balai Wilayah Sungai Sumatera VI Tahap II Dengan Metode DFBK dan DKI

Bintang Muliardi Utamas, Suhendra Suhendra, Wari Dony

Abstract


Analysis of calculations and planning in steel structures there are 2 methods that are usually used, the methods are the method load factor and resistance design (DFBK) and the method allowable strength design (DKI). The method DFBK is a method that takes into account the working load multiplied by several safety factors so as to produce a factored load which is then used to calculate or plan a building, while the method DKI is a method that does not depend on the combined load factor in the calculation and in its planning, but uses stresses. permission which basically this method emphasizes the duration factor of the load that occurs on the structure. In this case study, the author aims to compare the method DFBK and so what distinguishes the two methods in a gable frame steel portal building. Both methods use the H-Beam 200.200.7.11 steel profile for the column, the I-WF 200.100.5.5.5.8 steel profile for the beam, and the CNP steel profile 100.50.5.7.5 with internal force analysis on the steel portal carried out with the program SAP 2000 with loading in accordance with SNI 1727-2020 and the results of the program SAP 2000 taken the largest moment, shear and axial for the calculation of the steel structure portal. Based on the results of the calculation of the deflection of the method DFBK of 2.4 cm, the bolts used were 10 bolts and the base plate thickness was 15 mm. While the method DKI of deflection is 2.1 cm, the bolts used are 6 bolts and the base plate thickness is 14 mm. Based on the results of the study and the conclusion that the deflection of the method DKI is smaller than the method DFBK, the bolt requirements and base plate thickness of the method DFBK are closer in terms of construction, so the method DFBK is safer and stronger.


Keywords


Steel Structure Portal, DFBK, DKI, Workshop Building

Full Text:

PDF

References


Arifi, Eva dan Desy Setyowulan, 2021. “ Perencanaan Struktur Baja ”. UB Press, Malang.

Badan Standarisasi Nasional, 2020. “ Spesifikasi untuk bangunan gedung baja structural SNI 1729 - 2020 ”. Jakarta : Badan Standarisasi Nasional.

Badan Standarisasi Nasional, 2020. “ Beban minimum untuk perancangan bangunan gedung dan struktur lain SNI 1727 - 2020 ”. Jakarta : Badan Standarisasi Nasional.

Badan Standarisasi Nasional, 1989. “ Pedoman Perencanaan Pembebanan Umum Rumah dan Gedung

Cahya, Heppy Nur, 2014. “Studi Analisis Perbandingan Metode ASD (Allowable Stress Design) Dengan LRFD (Load and Resistance Factor Design) Pada Struktur Gable Frame Di Pembangunan Pasar Baru Kabupaten Lumajang”. Fakultas Teknik Sipil dan Perencanaan Institut Teknologi Nasional Malang.

Setiawan, Agus, 2008. “ Perencanaan Struktur Baja dengan Metode LRFD (Berdasarkan SNI 03-1729-2002) “.Erlangga. Jakarta.




DOI: http://dx.doi.org/10.33087/talentasipil.v5i2.141

Refbacks

  • There are currently no refbacks.


Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Jurnal Talenta Sipil, Faculty of Engineering, Batanghari University
Adress: Fakultas Teknik, Jl.Slamet Ryadi, Broni-Jambi, Kec.Telanaipura, Kodepos: 36122, email: talentasipil.unbari@gmail.com


Creative Commons License This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.